av receiver - Gizmodo

posts about #avreceiver more →
Mphony Is the AV Receiver I Want to Have
Samsung HT-AS720 Blu-ray Receiver Packs 5.1 Speaker System to Boot
Denon Hi-Def AV receiver Brings On the Video

Your version of Internet Explorer is not supported. Please upgrade to the most recent version in order to view comments.

Dsmvwl Admin Promote to frontpage Approve user Ban user ×

gallahad
09/29/09

In reply to Mphony Is the AV Receiver I Want to Have
Off-shoot question from a non-audio person... why does the default volume for receivers (0db), higher than what is a usual good volume? From the few I've had experience with, the usual good volume was around -20db and -25db.
Reply

valkilmerisawful promoted this comment gallahad was starred gallahad was unstarred

robots199
09/29/09

@gallahad: We went over this below...see bottom post.

READ BEFORE YOU POST!
Reply

robots199 was starred robots199 was unstarred

KefkaticFanatic
09/29/09

@robots199: That still doesn't explain what he's asking.
Reply

KefkaticFanatic was starred KefkaticFanatic was unstarred

valkilmerisawful
09/29/09

@gallahad: 0dB is the an averaged level of acceptable distortion for incoming signals. For example, going too far above 0dB, the outgoing analog signal becomes distorted and can suffer more from peaks and interference, albeit measurable by only a few percent. Go WAY beyond and the signal distorts further, probably by the same logarithmic scale as the dB system (that, I do not know).

Thus, the 0dB level is less of a measure of volume, like a car receiver, and more like a measure of the signal quality. Naturally, this translates to volume directly, but the purpose of having a 0dB default was to identify the signal strength with an low, acceptable distortion.

Was that your question? Anyone else have something to add? I'm no expert, so anyone is free to correct me, I love learning :)
Reply

valkilmerisawful was starred valkilmerisawful was unstarred

burninator
09/29/09

@KefkaticFanatic: I find it moderately humorous that Robots199 would lecture you on the subject of superfluous comments, as he currently has more then half the comments on this particular board.
Reply

The Lab promoted this comment burninator was starred burninator was unstarred

spannu
09/29/09

@valkilmerisawful: A decibel is just a ratio of the logarithms of two other measures, so it doesn't have to relate to distortion or power of a sound wave.

The displayed "volume" on a receiver just compares output volume to some reference volume which varies from device to device (usually related to the detection threshold for human ears), so the calculated dB may be different.

The reason why dB is used at all is because human ears can hear such a wide range of volumes that using logarithms compresses the range, and using dB should give an indication as to whether the sound is close to the minimum or maximum sound we can perceive.
Reply

spannu was starred spannu was unstarred

The Lab
09/29/09

@burninator: Agreed. When one violates his own decree, foolish he looks. So sayeth Yoda Confucius.
Reply

The Lab was starred The Lab was unstarred

valkilmerisawful
09/29/09

@spannu: See post by edd9000 below which expands upon my response. Yes, dB is relative. It is a relationship to the source input, and yes, it does measure "power" and "intensity". This is the logarithm of the ratios, not the ratio of the logarithms. Power and intensity only ever mean anything by comparison. I digress: the question was, "Why is 0dB the default for home AV equipment?" Because distortion is concurrently increased as the intensity is amplified. This is inherent to all signal processing. So 0dB is the maximum level at which the signal distortion is acceptable, even tho it's not likely audibly noticeable until you exceed 10 or 15dB above the 0dB reference. Hopefully we have answered that sufficiently (again, see below as well).
Reply

valkilmerisawful was starred valkilmerisawful was unstarred

Earlier discussions Other discussions Show all discussions Show featured discussions only Start a new discussion